SERVICE TECHNICIAN'S TROUBLE SHOOTING GUIDE FOR THE TRIANGLE …
Action Item:-Measure the BTU input to the boiler by clocking the gas meter or finding the oil flow rate based on nozzle size and Locate flow control devices (zone valve, spring check valves) or heat trap loops in the boiler piping close to the water heater. Insulate all boiler piping to and … Retrieve Content

SECTION 220500 – PLUMBING FIXTURES AND TRIM
Insulate all piping underneath. B. Approved alternate by Elkay or American Standard. 2.5 P-5 ACCESSIBLE WALL HUNG LAVATORY A. Kohler K-2030, "Greenwich", 20" x 1010 with sump receiver, underdeck clamp, extension, and cast iron dome. B. Approved alternate by Wade or Zurn. 2.12 P-12 DOWNSPOUT NOZZLE A … View Document

Ductwork
Insulate per Section 23 07 13. CASINGS AND PLENUMS – 6 inch W.G. PRESSURE CLASS Piping shall be installed with bracing as required to withstand the forces encountered during a cryogenic release event. … Retrieve Here

FIRE RESISTANT INSULATION For High Temperatures 2000 Nova …
Another impressive and documented feature of FireComp is its' ability to insulate against a 2200 degree flame from a 2" propane fueled nozzle. The probe attached to the backside registered only a maximum 243 degrees after nearly twelve hours of punishment. … Visit Document

GENERAL PROVISIONS
2” nipple and 100’ – 1-1/2” 50# test, unlined linen hose; 2-1/2”x1-1/2” reducer; 1-1/2” coupling; aluminum 1-1/2” fog nozzle A. Domestic Cold Water Piping: Insulate piping located in interior spaces as specified below. … Visit Document

Installation, Operation And Maintenance Manual
– Avoid contamination of unrelated bodies into the water piping during the unit connection to condenser pressure drop curves will result in unacceptable pressure drops, excessive nozzle Freeze point should be approximately 6°C below minimum design ambient temperature. • Insulate field water piping … Read Here

Static Electricity – Wikipedia, The Free Encyclopedia
Static electricity refers to the build-up of electric charge on the surface of objects. The static charges remain on an object until they either bleed off to ground or are quickly neutralized by a discharge. Static electricity can be with current (or dynamic) electricity, which can be delivered … Read Article

Blowdown Tanks For Process Steam Boilers
Do not insulate the tank. 5. For multiple boiler connections, continuous blowdown control, or install automatic aftercooler system at the tempered water outlet nozzle C . 6. Dashed lines indicate fi eld piping. The tempered water outlet nozzle shall be larger than the blowdown inlet nozzle for … Visit Document

Gaumer Hot Oil System Installation And Operation Manual
Air/Vapor bleed valves MUST be installed at high points in the piping to allow for venting of air/vapor. Insulate the piping for both energy conservation and personnel protection. Pressure (bubble) test the piping before loading the system with oil. 7. If the skid has a nitrogen blanket, connect the … Retrieve Here

INSTALLATION INSTRUCTIONS FOR MODELS JR-1 & JR-2
During the final installation, the steam nozzle supplied MUST be used. See "Steam Piping to Bath or Shower”. Insulate the steam pipe for maximum efficiency. WARNING: STEAM NOZZLE IS HOT. … Read Full Source

Weil McLain Troubleshooting Guide
Action Item: – Measure the BTU input to the boiler by clocking the gas meter or finding the oil flow rate based on nozzle size and Locate flow control devices (zone valve, spring check valves) or heat trap loops in the boiler piping close to the water heater. Insulate all boiler piping to and from … Content Retrieval

CLIENT INFORMATION
SPRAY NOZZLE REPLACEMENT *Replace upto 5 spray nozzles. RISER ADJUSTMENTS . FOR SPRAYS *Adjust or add risers upto 3 sprays *Excavating required *Does not include replacing spray body. PBV BACKFLOW REPLACEMENT *Replace upto 1 1/4” PBV backflow *Insulate outer piping around PBV … Retrieve Here

Condenserless Chillers 50/60 Hz
• INSULATE COOLER HEADS • 30HXA PIPING, VALVE, AND FAN CYCLING PRESSURE SWITCH INSTALLATION Flow switch factory installed in cooler inlet victaulic nozzle. NOTE: See Fig. 10 for weight distribution mounting points. … Fetch Doc